Call Us : +91-9022702227 info@aanuraj.com
SS 317L Stud Bolts, Hex Bolts & Nuts | UNS S31703 | Aanuraj
AANURAJ FASTENERS PVT. LTD.

Stainless Steel & High-Performance Industrial Fasteners

SS 317L Stud Bolts, Hex Bolts & Nuts – UNS S31703

Stainless Steel 317L (UNS S31703 / EN 1.4438) is a low-carbon, molybdenum-bearing austenitic stainless steel developed for improved corrosion resistance in many chemical and process environments. Its higher molybdenum content compared with 316L can improve resistance to pitting and crevice corrosion. Aanuraj Fasteners manufactures and supplies stainless steel threaded fasteners to customer drawings and agreed material, dimensional and inspection requirements.

Specification clarity: UNS S31703 identifies the 317L alloy chemistry; it is not, by itself, an ASTM A193 bolting grade. ASTM A193 B8M is associated with Type 316. If a project calls for 317L fasteners, the purchaser and manufacturer must agree the applicable product/bolting specification, material form, mechanical requirements, testing, marking and acceptance criteria in the purchase order. Do not claim ASTM A193 compliance based on chemistry alone.

Key features of SS 317L fasteners

Enhanced corrosion resistance

Higher molybdenum content than 316L improves resistance to pitting and crevice corrosion in many chloride-bearing and process environments.

Low-carbon austenitic grade

Carbon maximum of 0.030% helps reduce sensitization risk during welding and thermal exposure when suitable fabrication practices are followed.

Good fabrication characteristics

317L offers useful ductility and weldability. It is not hardenable by conventional heat treatment and can work-harden during cold deformation.

Why choose Aanuraj?

Specialist fastener manufacturing

Focus on stainless steel and high-nickel threaded fasteners, including studs, bolts and nuts for industrial service.

Quality and traceability

Material-document review, heat/lot identification, dimensional inspection and agreed testing documentation.

Application-focused support

Technical coordination on grade identification, dimensions, thread details, drawings and inspection requirements before dispatch.

Chemical composition of 317L (UNS S31703)

The following composition limits are commonly specified for 317L under ASTM A240/A240M product requirements for plate, sheet and strip. Values are weight percent (%). The applicable specification for the actual fastener raw-material product form must be checked separately; use the heat analysis on the MTC for acceptance.

ElementComposition (%)Metallurgical contribution
Carbon (C)0.030 maxLow carbon helps reduce sensitization risk
Chromium (Cr)18.00–20.00Forms the passive film for corrosion resistance
Nickel (Ni)11.00–15.00Stabilizes the austenitic structure
Molybdenum (Mo)3.00–4.00Improves pitting and crevice corrosion resistance
Manganese (Mn)2.00 maxComposition control and deoxidation
Silicon (Si)0.75 maxDeoxidation / composition control
Phosphorus (P)0.045 maxResidual element limit
Sulphur (S)0.030 maxResidual element limit
Nitrogen (N)0.10 maxComposition control
Iron (Fe)BalanceBase metal

Mechanical properties of 317L

Commonly published minimum room-temperature properties for annealed 317L plate/sheet to ASTM A240/A240M are shown below. These values are not automatically the acceptance limits for finished studs, bolts or nuts. Fastener properties must be established against the agreed fastener/product specification, raw-material form, size, condition and testing requirements.

PropertyTypical published minimum / limitUnit
0.2% proof / yield strength205 minMPa (N/mm²)
Tensile strength515 minMPa (N/mm²)
Elongation40 min%
Hardness95 maxHRB
DensityApprox. 8.0g/cm³
Modulus of elasticityApprox. 200GPa
Fastener engineering note: Do not use the above plate/sheet values as a substitute for bolt or nut proof-load, tensile, hardness or elongation requirements. Confirm the required fastener class/specification and test method before quotation and production.

Solution annealing heat-treatment process

317L is generally supplied in the solution-annealed condition. A commonly referenced solution-treatment range is approximately 1080–1175°C, followed by rapid cooling, commonly water quenching. The precise temperature, hold time, cooling method and acceptance criteria must follow the governing product specification and a qualified procedure.

1. PreparationVerify grade, heat number, MTC, load arrangement, furnace condition and calibrated temperature instrumentation.
2. HeatingHeat uniformly to the approved solution-annealing range, typically about 1080–1175°C for 317L reference practice.
3. SoakingHold according to a qualified procedure based on actual metal temperature, section size, load and governing specification. Avoid a universal fixed soak time.
4. Rapid coolingRapidly cool, commonly by water quenching where suitable and specified, to limit carbide re-precipitation and retain corrosion resistance.

317L is not hardenable by conventional heat treatment. The purpose of solution annealing is to restore a suitable solution-treated austenitic condition after processing. Record furnace calibration, load identification, temperature-time chart, soak, transfer/quench details and test results. Air cooling may be acceptable for some section sizes/procedures; follow the exact product specification rather than applying one quench method universally.

Manufacturing and quality checks

Raw material control

Check MTC, heat number, grade designation and chemical composition. PMI can be used as an additional identity check where specified.

Component manufacturing

Cutting, forming/forging, CNC machining and thread rolling or thread machining are selected according to component geometry and the approved route.

Final inspection

Verify dimensions, thread pitch and fit, surface finish, marking, traceability and specified mechanical tests. Supply reports as agreed in the order.

Industrial applications of SS 317L fasteners

317L fasteners may be considered for equipment and assemblies in corrosive process environments where its alloy chemistry is suitable after engineering review.

Chemical ProcessingPetrochemical PlantsPulp & PaperPower GenerationPollution ControlPharmaceutical EquipmentHeat ExchangersIndustrial PumpsProcess Piping

Final selection depends on chemical concentration, temperature, chloride level, flow, crevice geometry, stress, cleaning regime and galvanic conditions. 317L is not immune to all forms of corrosion; assess the actual operating environment before specifying the grade.

Aanuraj application experience: Hex bolts and nuts for a pump manufacturer

Aanuraj has manufactured and supplied stainless steel hex bolts and nuts for a pump manufacturer, supporting the fastening requirements of pump assemblies. The application called for attention to material identification, dimensional consistency, thread fit and dependable supply. This project experience reflects our focus on understanding the component's service conditions and manufacturing requirements before dispatch. Product grade and performance claims should always be supported by the customer's approved specification and inspection records.

Common questions about SS 317L fasteners

What is the UNS number for SS 317L?

The UNS designation for 317L is S31703. Its common European material number is 1.4438.

How is 317L different from 316L?

317L typically contains 3–4% molybdenum, compared with the lower molybdenum range of 316L. This can provide improved resistance to pitting and crevice corrosion in suitable environments. Actual service suitability depends on process conditions.

Is UNS S31703 an ASTM A193 grade?

UNS S31703 identifies the alloy, not an ASTM A193 grade designation. ASTM A193 B8M is associated with Type 316. If 317L bolting is required, the purchase order must identify the agreed applicable bolting/product specification and mechanical/testing requirements. Do not assume A193 compliance from the UNS number alone.

What is the solution annealing temperature for 317L?

Common technical references cite approximately 1080–1175°C followed by rapid cooling. Use the exact governing specification and qualified heat-treatment procedure for the product form and section size.

Can 317L be hardened by heat treatment?

No. 317L is an austenitic stainless steel and is not hardened by conventional quench hardening. It can work-harden during cold forming or machining.

What documents can be supplied?

Depending on the purchase order, documents may include MTC, heat/lot traceability, PMI report, dimensional inspection report, mechanical test report and third-party inspection records.

Request a technical quotation

Share your requirement for SS 317L studs, hex bolts or nuts, including diameter, length, thread standard, quantity, drawing, operating environment, applicable specification and required inspection documents.

Aanuraj Fasteners Pvt. Ltd.
Website: www.aanuraj.com
Email: sales@aanuraj.com
Phone: +91 90227 02227

Technical disclaimer: This page is an educational overview, not a replacement for licensed standards, customer drawings, engineering approval or a qualified heat-treatment procedure. Chemical composition and mechanical values shown are reference values tied to the stated product specification and form. Confirm the current standard edition, actual MTC, finished-fastener requirements, testing and acceptance criteria before manufacturing or inspection. Corrosion performance depends on service conditions and must be assessed by the responsible materials/design engineer.