Call Us : +91-9022702227 info@aanuraj.com
ASTM A193 Grade B8M SS 316 Stud Bolts and Nuts | Aanuraj Fasteners
AANURAJ FASTENERS PVT. LTD.

Stainless Steel Industrial Fasteners

ASTM A193 Grade B8M SS 316 Stud Bolts and Nuts

Aanuraj Fasteners manufactures and supplies stainless steel threaded fasteners for industrial service, including stud bolts, bolts and nuts. ASTM A193 Grade B8M is a stainless-steel bolting specification commonly associated with Type 316 stainless steel, selected for its molybdenum-enhanced resistance to pitting and crevice corrosion.

Specification note: ASTM A193/A193M covers bolting materials for high-temperature, high-pressure and other special-purpose applications. Confirm the applicable edition, grade, class, dimensions, mechanical requirements and supplementary requirements in the purchase order. Nuts may be specified under a separate applicable nut standard; do not assume every nut is automatically covered by A193.

Key features of B8M stainless steel fasteners

Molybdenum-bearing stainless steel

Type 316 typically contains 2.00–3.00% molybdenum, improving resistance to chloride-related pitting compared with Type 304 in many environments.

Industrial bolting specification

ASTM A193 Grade B8M defines requirements for stainless-steel bolting, including chemistry, mechanical properties, marking and heat-treatment condition as applicable.

Traceable quality control

For critical service, specify heat-number traceability, material test certificates, dimensional inspection and PMI/testing requirements in the purchase order.

Material names, standards and UNS designations

Common material nameUNS designationTypical product-standard referenceImportant distinction
Type 316 stainless steelS31600ASTM A240 (plate/sheet/strip chemistry); ASTM A193 Grade B8M for covered boltingGeneral 316 chemistry; carbon maximum is commonly 0.08% in product specifications.
Type 316L stainless steelS31603ASTM A240 for flat products; bolting grade/standard must be separately specifiedLow-carbon variant, typically carbon maximum 0.03%, intended to reduce sensitization risk after welding or thermal exposure.
Type 316H stainless steelS31609ASTM A240 for flat products; confirm the relevant product form and specificationControlled higher-carbon variant, typically 0.04–0.10% carbon, used where elevated-temperature strength is important.
ASTM A193 Grade B8MCommonly associated with Type 316 / S31600ASTM A193/A193MA bolting grade/specification designation, not simply a synonym for every 316-family material. Confirm class and required condition.

UNS identifies a material chemistry family; it does not by itself establish compliance with ASTM A193 bolting requirements. Standards can have product-form-specific limits and revisions. Verify against the exact standard edition and material test certificate for procurement or certification decisions.

Chemical composition comparison: SS 316, 316L and 316H

The following are commonly published composition limits for Type 316-family stainless steels in ASTM A240-type product specifications. Values are weight percent (%). The governing specification and product form must be checked before accepting material.

Element316 / S31600316L / S31603316H / S31609
Carbon (C)0.08 max0.030 max0.04–0.10
Chromium (Cr)16.0–18.016.0–18.016.0–18.0
Nickel (Ni)10.0–14.010.0–14.010.0–14.0
Molybdenum (Mo)2.00–3.002.00–3.002.00–3.00
Manganese (Mn)2.00 max2.00 max2.00 max
Silicon (Si)1.00 max1.00 max1.00 max
Phosphorus (P)0.045 max0.045 max0.045 max
Sulfur (S)0.030 max0.030 max0.030 max
Nitrogen (N)Specification-dependentSpecification-dependentSpecification-dependent
Does molybdenum differ between 316, 316L and 316H? In these common chemistry ranges, no: all three typically specify 2.00–3.00% Mo. The main named-grade difference is carbon content and its effect on sensitization and elevated-temperature properties. Actual heat chemistry may vary within the permitted range; use the MTC rather than assuming a fixed Mo percentage.

ASTM A193 B8M: class and supplementary requirement terminology

  • Grade B8M: Identifies the stainless-steel bolting grade associated with Type 316 chemistry.
  • Class: The class designation identifies a required condition and mechanical-property category. Solution-treated and strain-hardened conditions are not interchangeable; order the required class explicitly.
  • S1, S2, S3 and other “S” requirements: These are supplementary requirements in the ASTM A193 standard, not separate stainless-steel grades and not different molybdenum ranges. They apply only when specified in the purchase order. Their exact titles and requirements must be checked in the edition named by the contract.
  • 316 vs B8M: “316” is a stainless-steel type; “B8M” is an ASTM bolting grade designation. A chemical match alone does not prove that a finished stud bolt complies with ASTM A193.

Manufacturing process for SS 316 / ASTM A193 B8M stud bolts

Raw materialMTC + grade verification Cutting / formingCut length / forging if used Solution annealingControlled furnace cycle Rapid quenchUsually water quench ThreadingRolling / machining InspectionDimensions + properties Marking / traceabilityGrade, heat and lot Final releaseMTC + inspection records Actual sequence depends on product route, specified class, thread method and purchase requirements. Do not assume every B8M product uses the same forming or threading sequence.

Solution annealing temperature and quenching

Solution annealing is used to dissolve chromium-rich carbides and restore a suitable austenitic structure after prior processing. The treatment must be controlled to avoid sensitization during heating/cooling and to meet the specified ASTM A193 grade and class requirements.

Typical temperature range

For Type 316-family austenitic stainless steel, solution treatment is commonly around 1,040–1,120°C (1,900–2,050°F). The exact required temperature and soak practice depend on the applicable material specification, section size and approved heat-treatment procedure.

Soaking time

Use a qualified procedure based on actual metal temperature, cross-section, furnace uniformity and the governing specification. Do not set soak time from furnace set-point alone or use one time for every diameter.

Quenching

Rapid cooling, commonly by water quenching for suitable product sizes and approved procedures, helps prevent harmful carbide precipitation. Quench immediately after the required solution-treatment cycle; manage distortion, handling safety and water quality.

Manufacturing control: Do not treat the temperature range above as a substitute for the current ASTM A193/A193M requirements or the customer's approved procedure. Record furnace calibration, load/part temperature where required, soak, transfer time, quench method and test results. Confirm whether heat treatment must occur before or after final processing for the ordered class.

Quality checks for B8M stud bolts and nuts

  • Verify material identity and heat number against the material test certificate (MTC).
  • Review chemical composition, especially Cr, Ni, Mo and carbon, against the ordered grade and product specification.
  • Confirm the specified ASTM A193 grade and class, heat-treatment condition and mechanical-property requirements.
  • Inspect diameter, length, thread pitch, thread fit, straightness, chamfers and surface condition against the drawing and applicable dimensional standard.
  • Use PMI as a material-identification check where specified; PMI does not replace a full chemical analysis or the MTC.
  • Agree on supplementary testing, marking, inspection level, documentation and acceptance criteria before production.

Industrial applications

ASTM A193 Grade B8M SS 316 stud bolts and associated nuts may be specified for flanged joints, pressure equipment, valves, pumps, piping and structural connections in suitable service environments.

Oil & GasChemical ProcessingPetrochemical PlantsWater TreatmentMarine & CoastalIndustrial Piping

Final material selection depends on chloride concentration, temperature, stress, crevice conditions, cleaning chemicals and applicable design code. SS 316 is corrosion resistant, but it is not immune to chloride stress-corrosion cracking or localized corrosion in every environment.

Frequently asked buyer questions

Who manufactures ASTM A193 Grade B8M SS 316 stud bolts in India?

Aanuraj Fasteners Pvt. Ltd. is an Indian manufacturer of industrial threaded fasteners, including stainless-steel studs, bolts and nuts. Buyers should share the required diameter, length, thread standard, grade/class, quantity and inspection documents to confirm availability and compliance.

What is the molybdenum percentage in SS 316 and SS 316L?

The common specified molybdenum range for both Type 316 and Type 316L is 2.00–3.00% by weight. Check the applicable product standard and the actual heat analysis on the MTC.

What is the difference between SS 316 and ASTM A193 B8M?

SS 316 describes a stainless-steel type; ASTM A193 Grade B8M specifies requirements for covered bolting material. Compliance requires meeting the relevant specification, class, mechanical properties, condition and documentation—not chemistry alone.

What temperature is used for solution annealing SS 316 fasteners?

A common general range is approximately 1,040–1,120°C, followed by rapid cooling where required. The governing standard edition and approved procedure determine the actual process parameters for the product.

Request a technical quotation

For SS 316 / ASTM A193 Grade B8M stud bolts, share the material specification, class, diameter, length, thread form, quantity, operating conditions and required certificates.

Aanuraj Fasteners Pvt. Ltd.
Website: www.aanuraj.com
Email: sales@aanuraj.com
Phone: +91 90227 02227

Technical note: This page is an educational overview and not a replacement for the licensed current standards, customer drawings, engineering approval or an approved heat-treatment procedure. Confirm all acceptance limits against the purchase order and applicable standard edition before manufacturing or inspection.